Scientific journal
Fundamental research
ISSN 1812-7339
"Перечень" ВАК
ИФ РИНЦ = 1,674

Personal portfolio

ANISOTROPY OF THE STRUCTURE AND MECHANICAL PROPERTIES OF SYNTHETICMINERAL ALLOY

Ignatova A.M. 1 Ignatov M.N. 1 Artemov A.O. 1
1 National Research Perm Polytechnic University, Perm
The study results, which are presented in the article demonstrate the phenomenon of anisotropy of the structure and describe the nature of siminals their mechanical properties. Siminals tend to work better under static compressive loads than dynamic. Studied in detail the structure of various siminals identified features which explain the behavior of materials under different loads. Found that the smaller the size of crystalline components and the greater proportion of the amorphous phase, the more pronounced anisotropy, with the development of crystalline of the transverse strength increases at the expense of the longitudinal, with the development of overall cohesion strength is reduced. Heat treatment by which the adjusted ratio of the crystalline phase to amorphous and crystalline aggregates directly to the size of the structure should be administered not only in conformity with the requirements of the future strength of the product, but also in compliance with its configuration.
stone molding
synthetic mineral alloys
mechanical properties
the anisotropy of the structure
1. Kapica S.P. Sinergetika i prognozy buduwego. M.: Editorial URSS, 2002. 342 р.
2. Kurdjumov S.P. U istokov sinergeticheskogo videnija mira: rezhimy s obostreniem / S.P. Kurdjumov, E.N. Knjazeva // Samoorganizacija i nauka: opyt filosofskogo osmyslenija. M.: Argo, 1994. рр. 162–186.
3. Nikolis G. Poznanie slozhnogo. -M.: Editorial URSS, 2003. 344 р.
4. Ignatova A.M. Issledovanie i razrabotka shemy abrazivnogo iznashivanija poverhnosti sinteticheskih mineralnyh splavov sklerometricheskimi izmerenijami// Vestnik Tambovskogo universiteta, serija: Estestvennye i tehnicheskie nauki. no. 3, t. 15, 2010. pp. 1203–1208.
5. Ignatova A.M. Petrograficheskie issledovanija vzaimosvjazi struktury i svojstv bazaltovogo syrja i litja/A.M. Ignatova // Materialy 10-yh vserossijskih nauchnyh chtenij pamjati Ilmenskogo mineraloga V.O.Poljakova. Miass, 2009. pp. 45–49.
6. Ignatova A.M. Kristallizacionno-likvacionnaja model-shema formirovanija steklokristallicheskih materialov kamennogo lit / A.M. Ignatova, V.P. Chernov, A.M. Hanov // Materialy V-oj Vserossijskoj NTK «ANTJe-09» – Kazan: KGAU, 2009. pр. 235–237.
7. Ignatova A.M. Nanotverdost i osobennosti struktury sinteticheskogo kamennogo lit’ja/ A.M. Ignatova, A.M. Hanov// Materialy vserossijskoj molodezhnoj nauchno-tehnicheskoj konferencii «Novye materialy, nanosistemy i nanotehnologii». Uljanovsk, 2010. pр. 345–348.
8. Ignatova A.M.Issledovanie i razrabotka osnovnyh pravil upravlenija strukturnym mirom silikatov primenitelno k kamennomu litju/ A.M. Ignatova, V.P. Chernov, A.M. Hanov// Sb. tezisov II Vserossijskoj konferencii «Ot nanostruktur, nanomaterialov i nanotehnologij k nanoindustrii». Izhevsk: IzhGTU, 2009. pр. 45.
9. Ignatova A.M. Issledovanie kristallohimicheskoj sistematiki silikatov primenitel’no k kamennomu litju / A.M. Ignatova, A.M. Hanov// Materialy Mezhdunarodnoj konferencii studentov i molodyh uchenyh «Perspektivy razvitija fundamental’nyh nauk». Tomsk: TPU, 2009. pр. 38.
10. Ignatova A.M. Pravila upravlenija strukturoj i svojstvami kamennogo litja // «Vestnik Permskogo gosudarstvennogo tehnicheskogo universiteta «Mashinostroenie. Materialovedenie» . no. 3, t.14, 2010. pp. 67–75.
11. Chechulin V.A. Svojstva silikatnyh rasplavov dlja proizvodstva kamnelityh otlivok / V.A. Chechulin, Ju.G. Kovalev // Tr. XXI sovewanija po teorii litejnyh processov «Litejnye svojstva metallov i splavov». M: Nauka, 1967. pp. 356–378.
12. Hoek E. A simple triaxial cell for field and laboratory testing of rock // Trans. Instn Min. Metall. 1968, Vol. 77. pp. 22–26.
13. Stavrogin A.N. Prochnost gornyh porod i ustojchivost’ vyrabotok na bol’shoj glubine. M.: Nedra, 1986. 789 р.

Рецензенты:

Беленький В.Я., д.т.н., профессор, зам. директора, Западно-уральский аттестационный центр, г. Пермь;

Щицын Ю.Д., д.т.н., профессор, зав. кафедры «Сварочное производство и технология конструкционных материалов», Пермский национальный исследовательский политехнический университет,
г. Пермь.

 Работа поступила в редакцию 04.05.2012.